• Explosion Protection to EN, IEC
• Can be used in Zone 1, 2 Class 1 Division 2 Groups A,B,C,D
• Ex e structure, made of plastic, black.
• Single seal, suitable for unarmored cable
• Explosion protection to EN, IEC
• Can be used in Zone 1, 2, 21, 22 Class I Division 2 Groups A, B, C, D
• 2P, 3P, 4P and 5P.
• Only the switch in the socket cut off can plug be pulled out, power after inserting the plug.
• GRP (glass fibre-reinforced polyester resin)
• Explosion protection to CENELEC, IEC, NEC
• Can be used in Zone 0, Zone 1 and Zone 2/Zone 21 and Zone 22/Class I, Zone 1 and Zone 2/Class I, Division 2, Groups A,B,C,D
• Stainless steel enclosure
• Cable entries can be drilled, and components can be installed by user on request.
• International brand of explosion-proof terminal blocks.
• Explosion protection to CENELEC, IEC, NEC
• Can be used in Zone 0, Zone 1 and Zone 2/Zone 21 and Zone 22/Class I, Zone 1 and Zone 2/Class I, Division 2, Groups A,B,C,D
• GRP (glass fibre-reinforced polyester resin) enclosure
• Cable entries can be drilled, and components can be installed by user on request.
• Application, widely used on various marine platforms, chemical tankers, LNG ships and dangerous cargo wharfs for electric connection, or wire connection;
• Can reliably work in severe environment where is easily affected by moisture, vibration, or corrosion.
• Explosion Protection to EN, IEC
• Can be used in Zone 1, 2
• Lighting both in normal condition and emergency condition; When power supply is cut off, the emergency device starts to work; with overcharge, over-discharge protection and short circuit protection.
• With test pushbutton, convenient to check the emergency function. Press the test pushbutton, the light will switch into emergency condition.
• Ultra-bright LED lamp, low power consumption and long service life up to 50,000 hours; energy saving and environmental protection.
• Enclosure in Copper-free Aluminum Alloy, powder coated surface, yellow (RAL 1021).
• Toughened glass sheet resistant to temperature changes.
• Explosion Protection to EN, IEC
• Can be used in Zone 1, 2 Class I, Zone 1, 2 Division 1, Groups C, D
• Enclosure in Copper-free Aluminum Alloy, powder coated surface, yellow (RAL1021).
• Lighting angle can be adjusted.
• Low-power halogen tungsten lamps, with reflector to increase lighting intensity.
• Emergency device with Ni-MH batteries, charging automatically; when power supply is cut off, the emergency device starts to work; with overcharge and over-discharge protection.
• Toughened glass cover resistant to temperature changes.
• Explosion protection to EN, IEC
• Can be used in Zone 1,2,21,22 Class I, Zone 1,2 Division 2, Groups A, B, C, D
• Two enclosure types: 90, 160
• Applicable lamp and power (max.160W)
• LED: 60W, 90W, 120W, 160W
• Isolated LED lamp compartment, CC-CV (constant current – constant voltage) power controller compartment and terminal compartment; Wind-convection heat dissipation structure.
• New COB technology, large power and white light LED array, power of single LED can reach 20W~40W, high lighting efficiency, long service life.
• Two types of light distribution: spotlight and floodlight, which can be selected on request.
• 160 type lightings adopt light fitting integrated two lamps, the power of whole machine is of 2x120W,2X160W
• Low-maintenance due to long service life is up to 100,000 operating hours.
• Enclosure: Copper free aluminum, powder coated surface
• Explosion protection to EN, IEC
• Can be used in Zone 1,2,21,22 Class I, Zone 1,2 Division 1, Groups A, B, C, D
• Two enclosure types:50, 100
• Applicable lamp and power (max.100W)
• LED: 30W, 50W, 70W, 100W
• Isolated LED lamp compartment, CC-CV (constant current-constant voltage) power controller compartment and terminal compartment; Wind-convection heat dissipation structure
• Low-maintenance due to long service life is up to 100,000 operating hours.
• Enclosure: Copper free aluminum, powder coated surface
• Hazardous locations of zones 1 (gas) and 21 (dust) as standard illumination or as emergency illumination in combination with external power supply units.
• Housing: Glass fibre reinforced polyester resin.
• Cover: Injected polycarbonate, frosted (F) or clear, silicone gasket.
• Closure: Stainless steel clips (KE), two of them as safety clip (KES), to be opened with screwdriver only.
• Reflector: Aluminum, painted, carrying the encapsulated LED-modules and all electrical components, clipped into the cover, removable as a unit.
• LED modules with innovative encapsulation.
• The redesigned Areamaster provides greater versatility, with models from 9,000 to 19,500 lumens and from 24,000 to 38,000 lumens for the High Lumen version, and a choice of beam patterns to meet your diverse floodlighting needs.
• Typical applications include Oil and Gas Refineries, Petrochemical Plants, Foundries, Drilling Rigs, Pulp and Paper Mills, Food and Beverage Processing Facilities, Loading Docks, Power Plants, Water and Wastewater Treatment Facilities and other areas where corrosive, wet, dirty and tough environments are a problem.
• Rugged and compact housing with superior thermal design translates to long luminaire life
• Class I, Division 2, Groups A, B, C, D; Class I, Zone 2 Group IIC; Class II, Division 1 and 2, Groups E, F, G; Class III; Zone 20 and 21 Group IIIC; Zone 22, Group IIIB; Type 3R, 4, 4X, IP66/67; Simultaneous Exposure; Marine Outside Type (Salt Water) for USA ONLY; Wet Locations.
• Copperfree (4/10 of 1% max.) aluminum housing and lens door; silicone rubber gaskets; zinc plated HR steel yolk; stainless steel bolts, guard and safety cable; aluminum visor and (1) close up plug (provided).
• Reliable, light-weight, compact and ideal for task and area lighting applications.
• Typical applications include pulp and paper mills, processing plants, chemical plants, petrochemical facilities, oil refineries, drilling rigs, foundries, waste and sewage treatment facilities, mining and steel mills.
• Class I, Division 2, Groups A, B, C, D; Class II, Division 1 and 2, Group E, F, G; Class III; Class I Zone 2 AEx ec IIC; Zone 21 AEx tb IIIC; Class I Zone 2 Ex ec IIC; Zone 20 Group IIIC; Type 3R, 4, 4X; IP66/IP67; Simultaneous Exposure; Wet Locations & Marine Outside Type; IDA Approved with Visor.
• Standard version: Zone 2 and 21-22; Ex II 2 D; Ex II 3 GD; IP66; IK08
• Mounting hoods, bodies and guards are cast copper free (4/10 of 1% max.) aluminum with electrostatically applied baked gray epoxy-clad finish. Globes are polycarbonate or glass. Hardware, catch assemblies, guard are stainless steel. Refractors are heat-resistant prismatic glass
• LED explosion proof luminaire is certified for Class I, Division 1 locations and offers a full range of lumen outputs and mounting options.
• Typical applications include oil refineries, petrochemical facilities, pulp and paper mills, foundries, manufacturing facilities, waste and sewer treatment facilities, mining, and power generation facilities.
• Fixture housing and mounting hoods are copper free cast aluminum with baked epoxy finish. All exposed hardware is stainless steel.
• Class I, Division 1 and 2, Groups B, C, D; Class I, Zone 1, Group IIB + H2; Class II, Division 1, Group E, F, G; Class II, Division 2, Group F, G; Class III; Simultaneous Exposure; Type 3R, 4X; IP66/67; Suitable for Use in Wet Locations; Marine Outside Type (Salt Water); Approved for use in Paint Spray Booths